| | ƷƑ | | „ | Y|C | “ϵ҂
   ^oϵ
   Ęoϵ
    oϵ
  
   ֲoϵ
   woϵ
   㲿oϵ
   wzyϵ
  
  
 
“ϵʽ

ĴľO޹˾

E-mail: scgm@gmppe.com
ַɶнţ^·777̖C̳211110̖

  Fڵλ: „ӑB  

ţţߣС˵,վ,

rg2019-10-23  Դteacherschool.org

 

@xҪܡ܇ǰȻҪӰlәC܇𲽕r܇ǏȫoֹĠB𲽼ٵġϵ“ϵ܇clәCԵ“ϵt׃Ҽϙn܇ͻȻǰ_Ҽ£K𲽡@܇oֹǰ_raܴTlәCɺܴء@T£ţţߣС˵,վ,˲rgDټ½ͷD٣Ҽ300-500RPM£lәCϨܹȻ܇Ҳ𲽡

So we need the clutch. After the engine starts up, before the car starts, the driver first presses the clutch pedal, separates the clutch, causes the engine and the transmission system to detach, then puts the transmission gear into gear, then gradually releases the clutch pedal, causes the clutch to engage gradually.

  • (17)
  • In the joint process, the engine is gradually increased by the moment of resistance, so should step on the accelerator pedal gradually at the same time, that is, gradually increase the fuel supply to the engine, so that the engine speed is always maintained in the lowest stable speed, and do not stall. At the same time, as the engagement of the clutch gradually increases, the torque of the engine transmitted to the driving wheel by the transmission system will gradually increase, until the traction force is enough to overcome the starting resistance, the car will start from the static movement and gradually accelerate 2, to ensure that the transmission system shift smoothly

    ܇^Уm׃lϵҪQͬnλFX݆ʽ׃ēQnҼǓ܄X݆nCʹԭÙnλijҼX݆ƳӣʹҼnλX݆M빤ړQnǰ횲x̤壬ДӣʹԭnλćϸÓ_ͬrʹ™nλţţߣС˵,վ,帱ćϲλٶڅͬ@M뇧ϕrě_ԴĜpСFƽ혵ēQn

  • (26)
  • ܇MоoƄӕr]xtlәC͂ϵBӶD٣\ӼaܴđTأ䔵ֵܴ^lәCrlŤࣩϵɳ^ddɣʹCpġxxӲֺ͏ĄӲ֮gܮa\@ҼΣUˣ҂ҪxƂϵܵŤ࣬Cȫ

    xϵyĹDZClәCcϵyƽɿؽӺϣKܕrص׵طxӺָaĦأxָĦءxl܇r춻Ħøĥp׃λѵȣĦͣxϵyϡ˱MܵLxʹÉˣ_،xϵyMЧľSo@ஔҪ xʹ^УFĹҪx̤ء򻬡xص(ny)llJ푵ȡ

    1x̤صĹϬF ԭz򞷽S޹ϬF:_̤x̤,_ƣڣͬ܇vx̤@

  • (28)
  • The cause of the problem: 1) the separation of the total pump assembly: improper adjustment, pedal is too high, and no spare travel 2) driven plate assembly (lining) : lining abrasion quantity (wear to lining rivets) 3) clutch master cylinder, wheel cylinder, separation, separation fork bearing hairpin, movement is not flexible. 4) the flywheel face, pressure plate face wear big (wear more than 0.5 mm). 5) separation refers to excessive wear, which are smooth arc through your fingers, release bearing excessive wear surface grinding of concave arc (thrust).

    S޷: Ҽ:zx̤Ƿ^ߣгǷm{BϬF]tMҼ ڶ:zx̤塢áţţߣС˵,վ,塢xܲ桢xSеǷп,\Ӳ`F,x̤Ƿλ.ųȻܽQtMҼ :zxPɡwɡw݆Ƿĥp^PxָxSƽǷĥp^.PĦƬĥp©T;[˿ߜywɵĉPĥp0.3mm;w݆İbȳߜyĥpȑ0.5mm.;PxָˈA治ĥƽ;xSƽ治ĥ;ϳߴđQ^Б]ijҼҪrΪQ,Ҫ\y׸Q.(:xPĥp^,ֻQP,ҪͬrwɸQ)

     

      ӡ || P]
    | | ƷƑ | | „ | Y|C | “ϵ҂ | | O | ղ

     ĴľO޹˾ ַɶнţ^·777̖C̳211110̖

    |Wվ؈D